Greddy e-Manage Ultimate Installation Manual Bedienungsanleitung



4. Before InstallationCaution93. Initial SetupJumper LocationWhen Jumping “1-2” or “2-3” make sure to match the pin numbers printed on the circuit boa

5. How to splice wires1.Strip the wire as shown.6. How to install the connectors2.Wrap the stripped wire together as shown, and set the crimp in place

128. Wiring Power, Ground, Airflow Meter,Throttle, RPM Signal Hot-wire airflow meter, Flap type airflow meter, or Pressure sensor× ECU(En

138. Wiring Power, Ground, Airflow Meter,Throttle, RPM Signal for RB26DETT (with 2 airflow meters) × × Yellow (Airflow Input 2)White (Airflow Input 1)

for VTEC Equipped vehicle ECU(Engine Control Unit) Purple (VTM output)Light Blue (VTEC input)Yellow (VTEC output)× × Female connectorMale

• examples for ADD ONLY setup:1510. Injector Signal Wires • Wire the injector signal wires for each cylinders. (except for Rotary Engines).• Normally

1610. Injector Signal Wires # E× × × When changing I/J CHExample: Changing group injection to sequential injectionHow to connect• Connect the necess

× ECU(Engine Control Unit) Female ConnectorMale ConnectorSpliceBlue/Black (IG CH-1 OUT)Orange/Black (IG CH-2 OUT)Yellow/Black (IG CH-3 OU

1811. Ignition Signal Wire× × 26 pin connector*On Honda EG type vehicles, there are 2 ignition signals in the 26 pin connector. Group the 2 together a

Table Of Contents 1 1. Important Information 2 ~ 3 2. Unit Description 4 ~ 5 3. Initial Setup 6 ~ 9 4. Ho

19Vehicle Speed Signal wiring•Connect these wires to eliminate speed cut or when using the vehicle speed adjustment Map. These channels can also be u

2013. Crank & Cam Angle / Water & Intake Temp, Knock SignalCrank Angle Signal & Cam Angle Signal• Connect these wires for e-manage Ultimat

Device Connect to desired channelRelayRelay•These channels can be used for relays to activate desired devices. 14. NVCS / Relay Channels21NVCS (Nissa

2215. ECU Location ChartChannel Symbol DescriptionPowerGroundRPM SignalThrottle SignalAirflow/map Sensor SignalVTEC SignalVTM SignalSensor GroundCrank

16. ECU Wire Location Chart23TOYOTA / LEXUS Model Year Sensor Type CP # Chassis CodeEngi

16. ECU Wire Location ChartT−1T−12T−10T−8T−6T−4T−2T−3T−5T−7T−9T−11 ArI#1+BEtArI#3#4#1#2+BThEt#EArI#2#4#3#1+BThEt#ETh*1ArI#2#1+Bt#EE#E#2#1E Th#2Ar+B#E

2516. ECU Wire Location Chart

16. ECU Wire Location Chart26

2716. ECU Wire Location ChartNISSAN / INFINITI Model Year Sensor Type CP # Chassis CodeE

2816. ECU Wire Location Chart

1. Important Information2Please read this instruction manual carefully, and proceed with the installation ONLY if you fully understand this manual. Ma

2916. ECU Wire Location Chart Model

16. ECU Wire Location Chart30 * 2 Vehicle with VTMSignal*1 MT only

16. ECU Wire Location Chart31MITSUBISHILANCER3000

16. ECU Wire Location Chart32

16. ECU Wire Location Chart33MAZDA Model

16. ECU Wire Location Chart34MA−9+B#S2#S1#P2#P1ThE#EI・tLtTArI+BE?1Th#Et2・3t1・4ArI+BThEtL#ENeGW#1・3#2・4MA−2MA−4MA−3MA−6MA−8MA−10MA−5MA−7ArI+BThEtLArI+B

16. ECU Wire Location Chart35SUBARU Model

16. ECU Wire Location Chart36F−2Ｆ−1F−4Ｆ−3F−6Ｆ−5Ｆ−7ArI#2#4#3+BThE#1Ar#2#1#4#3+BI#4#3t1t2t3t4Ar+BThE#1#2#EI#4#3t2#Et1t3t4#1#2+BArTht1・2t1・2t3・4t3・4#ETh#

Notes37

Notes38

Caution!• Improper tuning of the e-Manage Ultimate can cause damage to the engine. • GReddy Performance Products, Inc. will not take

4

2. Unit Description5ACTIVE L.E.D• Steady GREEN - - - - - - When the unit recognize Ignition ON• Flashing GREEN - - - - - When Fouled Plu

63. Initial SetupJumper Setting• Before installing the unit, the Jumpers in the unit must be set for vehicle’s sensors, and desired maps for the a

3. Initial SetupJumper Setting DescriptionJP1 Injector Input / Output Signal CH1This jumper will configure the Injector Input / Output Signal CH1. S

83. Initial SetupJumper SettingJP11 OPTION 1This jumper will configure the OPTION 1 port on the Front Panel of the unit.Set to “OPEN” for Normal ty